Share
𝕏 Facebook LinkedIn

Effect of sputtering power on structural and optical properties of radio frequency-sputtered In2S3 thin films.

PAPER pubmed Journal of nanoscience and nanotechnology 2014 Other Effect: unclear Evidence: Insufficient

Abstract

In this study, we investigated the structural and optical properties of indium sulfide (In2S3) thin films as a substitute for the CdS buffer layer in Cu(In,Ga)Se2 (CIGS) solar cells. The In2S3 films were deposited on glass substrates using radio frequency (RF) magnetron sputtering. The sputtering power was changed from 60 to 120 W in 20 W increments. The effects of sputtering power on the crystallinity, surface morphology, and optical properties of the films were characterized with X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive X-ray spectroscopy (EDS), and UV-visible spectrophotometry. The XRD analyses indicated that the films were polycrystalline β-In2S3 structures with two preferred orientations along the (103) and (206) directions. The AFM images revealed that the films had nanosized grains and that the size increased from 7 nm for the samples prepared at 60 W to 13 nm for those prepared at 120 W. The optical band gap of the samples was found to vary between 2.88 and 2.43 eV.

AI evidence extraction

At a glance
Study type
Other
Effect direction
unclear
Population
—
Sample size
—
Exposure
radio frequency (RF) magnetron sputtering
Evidence strength
Insufficient
Confidence: 74% · Peer-reviewed: yes

Main findings

Indium sulfide (In2S3) thin films were deposited by RF magnetron sputtering with sputtering power varied from 60 to 120 W. Films were polycrystalline β-In2S3 with preferred orientations (103) and (206); AFM showed nanosized grains increasing from 7 nm (60 W) to 13 nm (120 W), and the optical band gap varied between 2.88 and 2.43 eV across samples.

Outcomes measured

  • Thin film crystallinity/structure (XRD)
  • Surface morphology/grain size (AFM)
  • Composition (EDS)
  • Optical properties/band gap (UV-visible spectrophotometry)
View raw extracted JSON
{
    "study_type": "other",
    "exposure": {
        "band": null,
        "source": "radio frequency (RF) magnetron sputtering",
        "frequency_mhz": null,
        "sar_wkg": null,
        "duration": null
    },
    "population": null,
    "sample_size": null,
    "outcomes": [
        "Thin film crystallinity/structure (XRD)",
        "Surface morphology/grain size (AFM)",
        "Composition (EDS)",
        "Optical properties/band gap (UV-visible spectrophotometry)"
    ],
    "main_findings": "Indium sulfide (In2S3) thin films were deposited by RF magnetron sputtering with sputtering power varied from 60 to 120 W. Films were polycrystalline β-In2S3 with preferred orientations (103) and (206); AFM showed nanosized grains increasing from 7 nm (60 W) to 13 nm (120 W), and the optical band gap varied between 2.88 and 2.43 eV across samples.",
    "effect_direction": "unclear",
    "limitations": [],
    "evidence_strength": "insufficient",
    "confidence": 0.7399999999999999911182158029987476766109466552734375,
    "peer_reviewed_likely": "yes",
    "keywords": [
        "In2S3",
        "indium sulfide",
        "thin films",
        "RF magnetron sputtering",
        "sputtering power",
        "XRD",
        "AFM",
        "EDS",
        "UV-visible",
        "optical band gap",
        "CIGS solar cells"
    ],
    "suggested_hubs": []
}

AI can be wrong. Always verify against the paper.

AI-extracted fields are generated from the abstract/metadata and may be incomplete or incorrect. This content is for informational purposes only and is not medical advice.

Comments

Log in to comment.

No comments yet.